- 您现在的位置：买卖IC网 > Sheet目录474 > MAX7036EVKIT-433+ (Maxim Integrated)EVAL KIT MAX7036
300MHz to 450MHz ASK Receiver
with Internal IF Filter
an error in the reference frequency. A crystal designed
to operate at a higher load capacitance than the value
specified for the oscillator is always pulled higher in fre-
quency. Adding capacitance to increase the load
capacitance on the crystal increases the start-up time
and may prevent oscillation altogether.
In actuality, the oscillator pulls every crystal. The crys-
tal’s natural frequency is really below its specified fre-
quency, but when loaded with the specified load
capacitance, the crystal is pulled and oscillates at its
specified frequency. This pulling is already accounted
Because the stray shunt capacitance at each of the
pins (IFC1 and IFC2) on a typical PCB is approximately
2pF, choose the value of the external capacitors to be
approximately 2pF lower than the desired total capaci-
tance. Therefore, the practical values for C9 and C10
are 22pF and 10pF, respectively.
MAX7036
for in the specification of the load capacitance.
Additional pulling can be calculated if the electrical
parameters of the crystal are known. The frequency
22k Ω
22k Ω
pulling is given by:
10
9
11
??
C CASE LOAD CASE SPEC ? ?
f P =
C M
2
?
?
+ C C + C
1 1 ?
? ? × 10 6
IFC1
IFC2
C10
C9
IFC3
where:
f p is the amount the crystal frequency is pulled in
ppm.
C M is the motional capacitance of the crystal.
C CASE is the case capacitance.
C SPEC is the specified load capacitance.
C LOAD is the actual load capacitance.
When the crystal is loaded, as specified (i.e., C LOAD =
C SPEC ), the frequency pulling equals zero.
It is possible to use an external reference oscillator in
place of a crystal to drive the VCO. AC-couple the exter-
nal oscillator to XTAL1 with a 1000pF capacitor. Drive
XTAL1 with a signal level of approximately -10dBm. AC-
couple XTAL2 to ground with a 1000pF capacitor.
IF Filter
The IF filter is a 2nd-order Butterworth lowpass filter
preceded by a low-frequency DC block. The lowpass
filter is implemented as a Sallen-Key filter using an
internal op amp and two on-chip 22k Ω resistors. The
pole locations are set by the combination of the on-chip
Figure 1. Sallen-Key Lowpass IF Filter
Data Filter
The data filter is implemented as a 2nd-order lowpass
Sallen-Key filter. The pole locations are set by the combi-
nation of two on-chip resistors and two external capaci-
tors. Adjusting the value of the external capacitors
changes the corner frequency to optimize for different
data rates. Set the corner frequency to approximately
1.5 times the fastest Manchester expected data rate
from the transmitter. Keeping the corner frequency near
the data rate rejects any noise at higher frequencies,
resulting in an increase in receiver sensitivity.
The configuration shown in Figure 2 can create a
Butterworth or Bessel response. The Butterworth filter
offers a very flat amplitude response in the passband
and a rolloff rate of 40dB/decade for the two-pole filter.
The Bessel filter has a linear phase response, which
works with the coefficients in Table 1.
resistors and two external capacitors (C9 and C10,
Figure 1). The values of these two capacitors for a 3dB
cutoff frequency of 400kHz are given below:
C 5 =
b
a ( 100 k )( π ) ( f c )
C 9 =
=
= 26 pF
=
= 13 pF
C 10 =
C 6 =
1 1
( 1 . 414 )( R )( π ) ( f c ) ( 1 . 414 )( 22 k Ω )( 3 . 14 ) ( 4 0 0 kHz )
1 1
( 2 . 828 )( R )( π ) ( f c ) ( 2 . 828 ) ( 22 k Ω )( 3 . 14 )( 400 kHz )
a
4 ( 100 k )( π ) ( f c )
where f C is the desired corner frequency.
_______________________________________________________________________________________
9
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
MAX7042EVKIT-433+
EVAL KIT MAX7042
MAX7044EVKIT-433
EVAL KIT MAX7044
MAX7058EVKIT+
EVAL KIT MAX7058
MAX7060EVKIT+
EVAL KIT MAX7060
MAX8506EVKIT
EVAL KIT FOR MAX8506
MAX8582ETB+T
IC CONV 1.5MHZ CDMA 10-TDFN
MAX9635ESA+
IC AMBIENT LIGHT SENSOR 8NSOIC
MAX9930EVKIT+
KIT EVAL FOR MAX9930
相关代理商/技术参数
MAX7036GTP/V+
功能描述:射频接收器 300MHz to 450MHz ASK Receiver with Internal IF Filter RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX7036GTP/V+T
功能描述:射频接收器 300 MHz/450MHz ASK Receiver W/Internal IF Filter RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX7036GTP/V+TW
制造商:Maxim Integrated Products 功能描述:300MHZ TO 450MHZ ASK RECEIVER WITH INTERNAL IF FILTER - Tape and Reel
MAX7036GTP/V+W
制造商:Maxim Integrated Products 功能描述:300MHZ TO 450MHZ ASK RECEIVER WITH INTERNAL IF FILTER - Rail/Tube
MAX7036GTP+
功能描述:射频接收器 300MHz/450MHz ASK Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX7036GTP+T
功能描述:射频接收器 300MHz/450MHz ASK Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
MAX703C/D
功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel
MAX703CPA
功能描述:监控电路 RoHS:否 制造商:STMicroelectronics 监测电压数: 监测电压: 欠电压阈值: 过电压阈值: 输出类型:Active Low, Open Drain 人工复位:Resettable 监视器:No Watchdog 电池备用开关:No Backup 上电复位延迟（典型值）:10 s 电源电压-最大:5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:UDFN-6 封装:Reel